View ATR0842_315949.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Features
* * * * * * * *
Current-controlled Output Current Source with 4 Input Channels Two Selectable Outputs for Grounded Laser Diodes Output A Suited for Blue Laser Diodes: VLD 6 V (VCCH 8 V) LVDS/CMOS Compatible Inputs Channel 2, 3, and 4 Output Current per Channel up to 350 mA Total Output Current up to 500 mA On-chip RF Oscillator Control of 2 Different Frequencies and Swings by Use of 4 External Resistors * Oscillator Frequency Range from 200 MHz to 500 MHz * Maximum Oscillator Current Amplitude 100 mApp * Small Pb-free QFN24 4 mm x 4 mm Package
www..com
Applications
* DVD Blue Laser * DVD-RAM/DVD-RW/DVD+RW with CD-RW Capability * Recordable Optical Drives
4-channel LVDS Laser Diode Driver with High Voltage Output for Blue Laser ATR0842 Summary
Description
The ATR0842 is a laser diode driver designed to operate two differently grounded laser diodes. The output, IOUTA, can be used for a blue laser diode (400 nm) with up to 6 V voltage drop by applying 8 V at pin VCCH. The other output, IOUTB, supports legacy laser diodes for DVD-RW/+RW/RAM (650 nm) and CD-RW (780 nm). The device includes four channels for four different optical power levels. The write channels (channel 2 to 4) can be controlled either by fast LVDS (Low Voltage Differential Signaling) or by single-ended standard CMOS logic. In case of single-ended use, each of the enable inputs (NEx or Ex) can be used, the complementary input may be left open. There is no need for blocking or connection to a reference voltage. The read function of the channel is to generate a continuous output current, channels 2 to 4 are designed as write channels with very fast switching speed. All channels are summed together and routed to one of the two outputs, IOUTA or IOUTB, controlled by the select input SELA. Each write channel (channels 2 to 4) can contribute up to 350 mA to the total output current of up to 500 mA. The read channel can contribute up to 150 mA. Total gain of 100 (read channel) and 250 (channel 2, 3 and 4), respectively, are provided between each reference current input and the selected output. Although the reference inputs are current inputs, voltage control is possible by using external resistors. An on-chip RF oscillator is available to reduce laser-mode hopping noise during read mode. The oscillator current amplitude can be set independently for the two selectable outputs with two different resistors. Oscillation is enabled by a high signal at the ENOSC pin. Complete shut down of the output currents is achieved by a low signal at the ENABLE input. In case of uncertain (balanced) enable signals, a built-in protection circuit keeps the laser diode output current within the defined range.
Rev. 4819AS-DVD-09/04
Figure 1. Block Diagram
I4 E4 NE4
www..com
Channel 4
I3 E3 NE3
VCCH Channel 3 IOUTA Output A
I2 E2 NE2
Channel 2
Output B IOUTB
IR
Channel 1 Read channel
ENABLE RF oscillator ENOSC
RFA RFB RSA RSB
SELA
2
ATR0842
4819AS-DVD-09/04
ATR0842
Pin Configuration
Figure 2. Pinning QFN24
I4 I3 I2 IR VCC VCCH
www..com
RFB RFA E2 NE2 E3 NE3
1 2 3 4 5 6
24 23 22 21 20 19 18 IOUTA 17 GND 16 RSA 15 RSB 14 IOUTB 78 13 SELA 9 10 11 12
Pin Description
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Paddle Symbol RFB RFA E2 NE2 E3 NE3 E4 NE4 ENOSC ENABLE VCC VCC SELA IOUTB RSB RSA GND IOUTA VCCH VCC IR I2 I3 I4 GND Type Analog Analog Digital Digital Digital Digital Digital Digital digital Digital Supply Supply Digital Analog Analog Analog Supply Analog Supply Supply Analog Analog Analog Analog Supply Function External resistor to ground sets frequency of oscillator B External resistor to ground sets frequency of oscillator A Digital control of channel 2 (high active) Digital control of channel 2 (low active) Digital control of channel 3 (high active) Digital control of channel 3 (low active) Digital control of channel 4 (high active) Digital control of channel 4 (low active) Enables RF oscillator (high active) Enables output current (high active) +5 V power supply +5 V power supply High: selects IOUTA, RSA, RFA Low: selects IOUTB, RSB, RFB Output current source B for laser diode External resistor to ground sets swing of oscillator B External resistor to ground sets swing of oscillator A Ground Output current source A for blue laser diode 8 V power supply for IOUTA +5V power supply Reference current input read channel (input impedance 500 to ground) Reference current input channel 2 (input impedance 500 to ground) Reference current input channel 3 (input impedance 500 to ground) Reference current input channel 4 (input impedance 500 to ground) Ground
E4 NE4 ENOSC ENABLE VCC VCC
3
4819AS-DVD-09/04
www..com
Absolute Maximum Ratings
Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Parameters Supply voltage High supply voltage Input voltage at any input Power dissipation Output voltage IoutB Output voltage IoutA Junction temperature Storage temperature Notes: 1. RthJA 115 K/W at Tamb = 70 C 2. RthJA 115 K/W at Tamb = 25 C Symbol VCC VCC Vin Pmax VoutB VoutB Tj Tstg Value -0.5 to +6.1 VCC to VCC + 2 -0.5 to VCC + 0.5 0.7
(1)
Unit V V V W V V C C
to 1
(2)
-0.5 to VCC - 1 -0.5 to VCC - 1.0 150 -65 to +125
Thermal Resistance
Parameters Junction ambient, QFN24 Note: Symbol RthJA Value 50
(1)
Unit K/W
1. Measured with multi-layer test board (JDEC standard)
Recommended Operating Range
Parameters Supply voltage High supply voltage Input current External resistor to GND to set oscillator frequency External resistor to GND to set oscillator swing Operating temperature range Symbol VCC VCCH IIR, II2, II3, II4 RFA, RFB RSA, RSB Tamb Value 4.5 to 5.9 VCC to VCC + 2.5 < 2.5 >3 >1 0 to +70 Unit V V mA k k C
4
ATR0842
4819AS-DVD-09/04
ATR0842
www..com
Ordering Information
Extended Type Number ATR0842-PFQG Package Lead free QFN24, 4 mm x 4 mm Remarks Taped and reeled
Package Information
5
4819AS-DVD-09/04
www..com
Atmel Corporation
2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600
Atmel Operations
Memory
2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314
RF/Automotive
Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759
Regional Headquarters
Europe
Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500
Microcontrollers
2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60
Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom
Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80
Asia
Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369
ASIC/ASSP/Smart Cards
Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743
Japan
9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581
Literature Requests
www.atmel.com/literature
Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company's standard warranty which is detailed in Atmel's Terms and Conditions located on the Company's web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel's products are not authorized for use as critical components in life support devices or systems.
(c) Atmel Corporation 2004. All rights reserved. Atmel(R) and combinations thereof are the registered trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be the trademarks of others. Printed on recycled paper.
4819AS-DVD-09/04

▲Up To Search▲

Price & Availability of ATR0842

	To Download ATR0842 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .